Xtreme Polishing Systems | Surface Preparation Machines Equipment, Concrete & Epoxy Supply > Equipment > Floor Burnishers & Buffers >

NSS Charger 1500 Burnisher
NSS Charger 1550 High Speed Burnisher | Xtreme Polishing Systems (877) 958-5264


 
Finance as low as $42.80/month
Our Price: $3,382.00

Availability: Usually Ships in 24 Hours
Product Code: NSS-5205232
Qty:

Description
 

NSS Charger 1500 Floor Burnisher

The NSS Charger 1500 Floor Burnisher has an advantage no other machine can claim. It can be used on a polymerized acrylic floor finish reinforced with metal interlock immediately after it has dried. Because of its lightweight. The charger will not gouge the finish or destroy the setup of the metal interlock. In fact, the top film hardens, resulting in an immediate gloss. At the same time, Charger's ultra-high-speed burnishing tends to drive off excess plasticizers, hastening the hardening process and preventing soiling. The new finish can be maintained in a regular manner from the start.

Versatile Charger 1500 allows you to burnish and spray buff. Strong enough to use for damp scrubbing prior to recoating. Remove worn top coats of finish without flood stripping. Exceptionally quiet and super dependable. The Charger 1500 is a signature machine in the NSS line. This burnisher represents the very definition of versatility, at 1500 RPM, it can burnish, spray buff, and damp strip. An aggressive pad speed and rugged construction enable it to produce that ultra-gloss wet-look shine year after year.

Features & Benefits:

  • Pad Speed: 1,500 rpm
  • Pad Size: 20in
  • Pad Driver: 19" structural foam, rigid back
  • Motor: DC rectified permanent magnet, 66 frame, 115V (240V available), 1.5 HP, 3,000 rpm
  • Current: 13 amps @ 115V (under typical burnishing conditions)
  • Overload Protection: 17.5 amp reset the circuit breaker
  • Drive: Belt and Pulley
  • Base: Polished cast-aluminum
  • Wheels: Two (2) 5" non-marking rubber
  • Handle: Removable 1.5" dia. Steel tube
  • Switch: (On-off): Dual dead-man levers w/mechanical lockout
  • Cord: 75', 14-3 SJT safety yellow
  • Increased Power--The motor packs more power when you need it and is designed for long-running life
  • Extra Protection--The motor is protected in two ways; dual rectifiers divide electrical load, and a circuit breaker prevents operator-induced overloads
  • Easily Serviceable--The machine is constructed so users can do ordinary service right on the job. Most other machines must be returned to a service center for repairs
  • Added Security--The short fixed handle enables the operator to easily operate the machine, walk with comfort, and perform short-radius turnarounds, maintaining control in congested areas and constant pressure on the pad
  • 1.5 dia. The steel handle is removable for machine transport and reverses for machine storage
  • Mechanical lockout prevents accidental starts and unauthorized use
  • Dual switch levers
  • Reset circuit breaker protects the motor against operator-induced overloads
  • Heavy-duty cord strain relief
  • Bearing is mounted in a pillow-block arrangement for low heat rise and extended bearing life
  • 75' safety yellow cord for minimal outlet changes. Cord hook
  • Structural foam, the rigid-back driver is factory aligned to deliver maximum burnishing performance and reduced running amps (U.S. Patent #4,122,576)
  • Handle release lever-up to securely lock handle in place, down to remove
  • Wheel carriage (standard on Model No. 5205234) simplifies machine transport, pad changes and moving up and downstairs
  • Non-marking bumper to protect walls and baseboards
  • Polished cast aluminum base is virtually indestructible
  • 1.5 hp motor for long life and aggressive burnishing

Share your knowledge of this product. Be the first to write a review »

Browse for more products in the same category as this item:

Equipment > Floor Burnishers & Buffers
Shop Products > By Brand > NSS